Din varukorg

Frakt / upphämtning ingår alltid i varje beställning.
Din varukorg är tom
Lägg till ett test för att komma igång
Bläddra bland tester
Cosmetic Testing Lab

Talc in Cosmetics: Asbestos Testing Rules Under MoCRA

november 21, 2026  ·  8 min läsning

Talc in Cosmetics: Asbestos Testing Rules Under MoCRA

Talc is a common powder in blush, eyeshadow, face powder and baby products, and talc asbestos testing for cosmetics is one of the most watched parts of the Modernization of Cosmetics Regulation Act (MoCRA). The law told the FDA to set standard test methods, the agency proposed a rule at the end of 2024, and then withdrew it a year later. This guide explains where things stand, what the withdrawn proposal would have required, and what a careful brand should do while the rule is rewritten.

Innehåll
  1. The short answer
  2. Why is asbestos a concern in talc?
  3. What does MoCRA require?
  4. What did the December 2024 proposal say?
  5. Why was the proposal withdrawn?
  6. What should brands do now?
  7. How does this connect to safety substantiation?
  8. What about the EU?
  9. Common mistakes
  10. Frequently asked questions
  11. Key takeaways

The short answer

MoCRA requires the FDA to issue regulations that set standardized methods for detecting and identifying asbestos in talc-containing cosmetics. The FDA proposed such a rule in December 2024, but withdrew it on 28 November 2025 to reconsider it after public comments. Today there is no FDA-mandated test method, so testing is a matter of your own safety substantiation, supplier controls and risk management, and a reissued rule is expected but has no published date. We do not run asbestos tests ourselves; asbestos analysis is specialised electron microscopy work done by dedicated laboratories.

Why is asbestos a concern in talc?

Talc and asbestos are both naturally occurring minerals, and they can occur close together in the ground. The FDA states that talc can be contaminated with asbestos, which is why mining sites must be chosen carefully and the ore tested sufficiently. The agency has run several surveys. A 2009–2010 survey, using polarized light microscopy (PLM) and transmission electron microscopy (TEM), found no asbestos in the products tested, but the FDA noted its limits: only four of nine talc suppliers sent samples and few products were tested, so it did not prove that most talc is free of asbestos. In 2019 and 2020 the FDA tested products after reports of contamination; in October 2019 it issued a safety alert about certain products that tested positive, and one baby powder was voluntarily recalled. The FDA also tested talc-containing cosmetics in 2021, 2022 and 2023.

Läs också Reglering av nanomaterial i kosmetika: regler och anmälan

What does MoCRA require?

MoCRA includes a section directing the FDA to establish and require standardized testing methods for detecting and identifying asbestos in talc-containing cosmetic products. The statutory deadline was about a year after the law was enacted in December 2022, and it was missed. The law asks the FDA to set the test methods; it does not itself name the methods, which is why the content of the rule matters so much.

What did the December 2024 proposal say?

The FDA announced the proposed rule on 26 December 2024. In summary, it would have:

  • applied to manufacturers of talc-containing cosmetic products and to the talc ingredient used in them;
  • required testing of representative samples from each batch or lot, either of the finished product or of the talc ingredient;
  • required two methods run together: PLM with dispersion staining, and TEM with energy-dispersive spectroscopy and selected area electron diffraction (TEM/EDS/SAED);
  • allowed a manufacturer to rely on a talc supplier’s certificate of analysis if it qualified the supplier through verification testing;
  • included recordkeeping provisions;
  • made a product adulterated if it failed the testing or recordkeeping provisions, or if asbestos was found.

The FDA also said that methods such as X-ray diffraction and infrared spectroscopy were not sensitive enough.

Timeline of the FDA talc asbestos testing rule from MoCRA to its withdrawal, and the steps brands should take now.

Why was the proposal withdrawn?

The FDA withdrew the proposal on 28 November 2025, stating that the comments warranted further consideration and assessment before issuing final regulations. According to legal commentary, commenters including the United States Pharmacopeia argued mainly that the proposed TEM method may not reliably distinguish asbestiform from non-asbestiform particles, which could produce many false positives; the USP approach uses PLM with X-ray diffraction. Others raised concerns about a broad definition of asbestos that differs from the ones used by other federal agencies. The withdrawal is described as a reconsideration of how to test, not as the end of testing. Because the mandate stays in the statute, a new proposal should follow, with another chance for public comment. No timeline has been published.

Läs också CMR-ämnen i kosmetika förklarade: vad som är förbjudet

What should brands do now?

With no mandated method, the sensible path is to behave as if a rule is coming, without locking into details that may change:

  1. List every product containing talc. Check powders, blushers, eyeshadows, bronzers, baby products and anything with “talc”, “magnesium silicate” or “hydrated magnesium silicate” in the ingredient list.
  2. Ask the supplier for the full picture. Request a lot-specific certificate of analysis that states the test method (PLM, TEM, XRD or a combination), the laboratory, the detection limit and the result for asbestos. Ask about the mine source and whether it changes between lots.
  3. Verify independently. A periodic check by an independent, accredited laboratory with electron microscopy capability gives you data that does not depend only on the supplier’s paperwork.
  4. Keep records by lot. Link each finished batch to the talc lot and its certificate. If a rule requires lot-level records, you already have them.
  5. Decide on talc-free. For some products a talc-free formula (for example with mica, silica or starch-based powders) avoids the issue, but each alternative has its own safety and performance profile and still needs assessment.

How does this connect to safety substantiation?

MoCRA requires the responsible person to keep records supporting adequate safety substantiation for each product. The FDA says neither the law nor its regulations require specific tests, so the brand decides what is adequate. For a talc product, a documented asbestos-control approach is a natural part of that file: supplier specification, certificates, independent verification and your decision logic. If an authority, retailer or customer asks, a clear file is far better than a verbal assurance. Our overview of what a CPSR contains shows how this kind of evidence is organised in the EU.

Lab worker pouring liquid into a beaker

What about the EU?

The EU has no asbestos test standard written into its cosmetics law, but it handles the question through the safety assessment. As we understand the annexes of Regulation (EC) No 1223/2009, asbestos is prohibited in cosmetics, and talc is listed as a restricted substance with a warning for powders intended for young children; check the current consolidated text before relying on this. The CPSR must also address impurities and traces in the ingredients. Part A of Annex I asks for information on purity, impurities and traces, so a safety assessor will expect a talc specification and asbestos-free evidence from the supplier, and a record of how the supplier’s claim was verified. If you sell in both markets, one well-built talc dossier can serve both. The assessor also relies on stability and microbiological data for the same product, but purity and impurity evidence is a separate item that only the talc supplier and a specialised laboratory can provide.

Läs också Säkerhetsmarginal (MoS) för kosmetika: så beräknas den

Common mistakes

  • Relying on a generic “asbestos-free” statement without a method, laboratory or lot number.
  • Accepting a certificate that only used a method with a high detection limit.
  • Qualifying the supplier once and never checking again as lots change.
  • Ignoring talc that arrives inside a bought-in blend or colour premix.
  • Assuming the withdrawal means testing is no longer needed.

Frequently asked questions

Is asbestos testing of talc cosmetics mandatory in the US right now?

There is no FDA rule that prescribes a method or frequency at the moment. The mandate to create one remains in MoCRA. Brands remain responsible for the safety of their products, and many already test or require certificates.

Which method is best, PLM, TEM or XRD?

That is exactly what the FDA is reconsidering. The proposal chose PLM plus TEM; critics prefer approaches such as PLM with XRD. Ask your laboratory which method fits the talc source and why, and keep the method name in your records.

Can you test my talc for asbestos?

No. We do not run asbestos tests. We can help you build the safety documentation around the data, including the CPSR, and you can obtain asbestos analysis from a specialised laboratory.

Key takeaways

  • Status: MoCRA requires standard talc asbestos test methods, but the December 2024 proposal was withdrawn on 28 November 2025.
  • Today: no FDA-mandated method, so supplier controls and your own substantiation carry the weight.
  • Prepare: lot-level certificates, independent verification and traceability from talc lot to finished batch.
  • EU: the safety assessment expects purity and impurity data for talc in the CPSR.
Källor (6)
Källa Utgivare Länk
Talc U.S. Food and Drug Administration fda.gov/cosmetics/cosmetic-ingredients/talc
FDA Issues Proposed Rule for Testing Methods for Detecting and Identifying Asbestos in Talc-Containing Cosmetic Products U.S. Food and Drug Administration fda.gov/cosmetics/cosmetics-news-events/fda-issues-proposed-rule-testing-methods-detecting-and-identifying-asbestos-talc-containing-cosmetic
FDA Withdraws Standardized Asbestos Testing Proposal for Talc-Containing Cosmetics Wiley Rein LLP wiley.law/alert-FDA-Withdraws-Standardized-Asbestos-Testing-Proposal-for-Talc-Containing-Cosmetics-With-Intent-to-Reexamine-and-Reissue
Modernization of Cosmetics Regulation Act of 2022 (MoCRA) U.S. Food and Drug Administration fda.gov/cosmetics/cosmetics-laws-regulations/modernization-cosmetics-regulation-act-2022-mocra
Regulation (EC) No 1223/2009 on cosmetic products European Union (EUR-Lex) eur-lex.europa.eu/eli/reg/2009/1223/oj
Implementing Decision 2013/674/EU: guidelines on Annex I (CPSR) European Union (EUR-Lex) eur-lex.europa.eu/eli/dec_impl/2013/674/oj

Läs också

Alla artiklar →
Spara 10 % på din första beställning och 20 % på paket!
Paketrabatt för alla. För 10 %: skapa ett gratis konto och bekräfta din e-post.
Kom igång

CPSR-säkerhetsrapport: redigera ett tidigare dokument eller börja ett nytt?

Lagt i varukorgen

Din CPSR-säkerhetsrapport och allt du fyllt i finns nu i din varukorg. Gå till kassan för att slutföra beställningen eller fortsätt lägga till tester – dina svar följer med den här artikeln.

Gå till kassan
Beställ CPSR-rapport
Utkast återställt
1
Företag
2
Produkt
3
Förpackning
4
Formulering
5
Tester
6
Förpackningsdesign
7
Granska

Fyll i produktformuläret. Våra säkerhetsbedömare bekräftar din beställning inom kort.

I. Person / företag som beställer säkerhetsbedömningen
II. Produktinformation
III. Användningsvillkor och förpackning
IV. Produktformel
#INCI-namnCAS-nummerNano% i produkten
Kan innehålla
Totalt0/ 100%
V. Specifikationer och tester av den färdiga produkten

Ett utmaningstest krävs för alla kosmetiska produkter utom sådana med låg mikrobiologisk risk, nämligen:

  • Produkter som inte innehåller vatten eller har låg vattenaktivitet
  • Produkter med ett pH under 3 eller över 10
  • Produkter som innehåller mer än 20 % alkohol
  • Produkter som innehåller råvaror som skapar en fientlig miljö (starka oxidationsmedel, polära organiska lösningsmedel, oxiderande färgämnen, aluminiumklorhydrat och liknande salter, drivgaser med mera)
  • Produkter som fylls i behållare vid mer än 65 °C
  • Produkter som förpackas i trycksatta behållare, pumpdispensrar eller endosförpackningar
När krävs inget utmaningstest?

Ett utmaningstest krävs för alla kosmetiska produkter utom sådana med låg mikrobiologisk risk, nämligen:

  • Produkter som inte innehåller vatten eller har låg vattenaktivitet
  • Produkter med ett pH under 3 eller över 10
  • Produkter som innehåller mer än 20 % alkohol
  • Produkter som innehåller råvaror som skapar en fientlig miljö (starka oxidationsmedel, polära organiska lösningsmedel, oxiderande färgämnen, aluminiumklorhydrat och liknande salter, drivgaser med mera)
  • Produkter som fylls i behållare vid mer än 65 °C
  • Produkter som förpackas i trycksatta behållare, pumpdispensrar eller endosförpackningar
VI. Produktförpackning och förpackningsdesignValfritt — vi kontrollerar etiketten mot den färdiga CPSR, så designen för ytterförpackningen och primärbehållaren hjälper till. Du kan också skicka den till oss senare.
VII. Granska din beställning
Pris—

Säkerhetsdatablad: redigera ett tidigare dokument eller börja ett nytt?

Lagt i varukorgen

Din Säkerhetsdatablad och allt du fyllt i finns nu i din varukorg. Gå till kassan för att slutföra beställningen eller fortsätt lägga till tester – dina svar följer med den här artikeln.

Gå till kassan
Beställ säkerhetsdatablad (SDS)
Utkast återställt
1
Kund
2
Formulering
3
Språk
4
Detaljer
5
Granska

Fyll i formuläret nedan. Vi tar fram ditt REACH-kompatibla SDS med snabb leveranstid.

I. Information om kunden
Kunden
Innehavare av SDS
II. Information om produktens formel
#INCI-namnCAS-nummer% i produkten
Totalt0/ 100%

Lång ingredienslista? Utgå från vårt kalkylblad.

Ladda ner mallen, fyll i den i Excel, Numbers, LibreOffice eller Google Sheets och ladda sedan upp den här – varje fält hamnar på rätt plats. Att fylla i formuläret för hand fungerar lika bra.

Ladda ner mall (.xlsx) eller .csv
III. Regelområde och språkversionerEtt SDS måste tillhandahållas på det officiella språket i varje marknad där produkten släpps ut. Välj varje marknad du distribuerar till — vi utfärdar en språkversion per val.
0 valda
IV. Ytterligare information om produktenAllt i detta steg är valfritt, men ju mer du ger oss, desto snabbare kan vi färdigställa SDS:et.
V. Granska din beställning
Från—
Beställningsuppgifter

Allt du fyllt i för den här artikeln.

Så fungerar det

Två sätt att bli redo för marknaden — välj det som passar dig.

Jag vet vad jag behöver

Välj tester & gå till kassan

1 Lägg tester i varukorgen & gå till kassan
2 Vi ordnar gratis DHL-upphämtning av dina prover
3 Vi testar dem och du får resultaten
Beställ tester & CPSR

Jag är osäker på vad jag behöver

Lägg till produktinformation & få rekommendationer

1 Logga in & lägg till produktinformation för att se vad du behöver
2 Beställ de tester som behövs — vi ordnar upphämtningen
3 Du får resultaten när vi är klara med testerna
Kom igång
Fortfarande osäker? Svara på frågeformuläret